No. 12 & 13 Hanover Road, Workington
info@splash.co.zw
VoIP: 086 7700 7190

Paints

SMOOTH COAT

Available in 20 Litres

CEILING PAINT

Available in 20 Litres

ROOF PAINT

Available in 20 Litres

WASH AND SHINE

Available in 5 Liters & 20 Litres

INTERIOR EXTERIOR

Available in 5 Liters & 20 Litres

ACRYLIC PVA

Available in 5 Liters & 20 Litres

GLOSS ENAMEL

Available in 1 Litre & 5 Litres

WOOD VARNISH

Available in 1 Litre & 5 Litres

BRICK CARE

Available in 1 Litre & 5 Litres

ROADLINE PAINT

Available in 1 Litre & 5 Litres

GREY PRIMER

Available in 1 Litre & 5 Litres

PINKWOOD PRIMER

Available in 1 Litre & 5 Litres

RED OXIDE METAL PRIMER

Available in 1 Litre & 5 Litres

ZINC PRIMER

Available in 1 Litre & 5 Litres

UNIVERSAL UNDERCOAT

Available in 1 Litre & 5 Litres

MORE SPLASH PRODUCTS

ROOF SEAL

Available in 5 Litres

*All pictures shown are for illustration purposes only. Actual product may vary due to product enhancement.

Bonding Liquid

Description

Splash Bonding Liquid is based on long oil alkyd resin and is supplied at a low viscosity to give it the penetrating and bonding properties. It is designed for use on friable and loosely bound plasters where it bonds the loose or under-bound materials to a hard impenetrable surface. It is also used on old loosely bound coatings such as distemper. It is compatible with alkyd and emulsion based topcoats.

Properties

Vehicle type: Long Oil Alkyd resin.

Solvent: White Spirit

Finish: N/A

Pigment type: It is non-pigmented

Theoretical coverage: 6 – 8 square metres per litre depending on surface porosity.

Colour range: Clear

Thinner: Supplied Ready For Use.

Drying time: Touch dry: 4 hrs at ambient temperatures and relative humidity.

Hard dry: 16 hours.

Shelf life: Splash Bonding Liquid is stable up to 24 months in sealed containers. Paint should not be left in partially filled containers to avoid formation of skin and subsequent gelling.

Pack size: 5 litres, 1 litre

 

Application method

Application is by brush or spraying.

 

Compatibility with other paints

Splash Bonding Liquid is compatible with alkyd and emulsion based paints.

 

Surface preparation

New and friable/porous Plaster

The surface is brushed with soft bristle brush and dusted off until all loosely bound materials are no longer present.

Old surface with loose and flaking materials

Previously painted surface with old and loose flaking paint, such as distemper, is thoroughly sanded down with coarse sand paper and dusted off. The sanding should be done until only strongly bound material is left.

Storage conditions

Paint should be stored in a cool, dry environment away from direct sunlight, heat and frost conditions. Tins should be kept tightly sealed to prevent skinning and gelling.

Aluminium Paint

Description

Splash Fencing Aluminium is formulated from a solid hydrocarbon resin and pigmented with leafing aluminium. It dries to a bright aluminium finish. Fencing Aluminium is primarily used on fencing posts as well as other suitably primed metallic and non-metallic surfaces.

 

Properties

Vehicle type: Solid Hydrocarbon resin

Solvent: White spirit

Theoretical coverage: 8 - 10 square metres per litre at DFT 50 microns.

Finish: Bright aluminium

Pack size:  5 litre, 1 litre.

Thinner: Supplied Ready For Use

Drying time: Touch Dry 15 minutes  @ 25 degrees Celcius.

Hard dry: 1 hour @ 25 degrees Celcius.

Life span of coating: The dry film of Fencing Aluminium has a life span of up to 24 months when the bright aluminium finish is still visible. However the finish dies away with time due to exposure to weather elements.

 

Shelf life: The shelf life of Fencing Aluminium is 12 months. Containers of Fencing Aluminium should be kept tightly closed away from moist, alkaline or acidic environment. The Aluminium pigment reacts with both acids and alkalis to release some gases which causes the tins to bulge and/or explode.

 

Application method

Fencing Aluminium is applied by brush or spraying. Turpentine is used to clean brushes after painting.

 

Compatibility with other paints

Fencing Aluminium is compatible with alkyd-based coatings.

 

Surface preparation

All surfaces must be dry, free of dust, oily materials and loose flakes. Old fencing posts must be de-rusted with a wire brush and the appropriate primer applied.

Storage conditions

Fencing Aluminium should be stored at room temperature away from direct sunlight. Acidic and alkaline conditions should be avoided.

Epoxy Floor Coating

Product Description
It consists of Resin and Hardener mixed together in the ratio 4:1 by volume where they react chemically to form rigid plastic material that is strong, resistant to degradation and bonds extremely well to its substrate.

Properties & Benefits
Its excellent durability makes it ideal for indoor application. Epoxies tend to chalk when used for outdoor application. Suitable for floor coating protection of garages, commercial and industrial flooring. Ensure an economical alternative to tiling in low cost.

Specific Gravity - 1.27

Viscosity at 25 Deg C -  70 - 75 KU when mixed Base and Hardener

Colour - Grey

Finish Gloss - 85 – 100%

Spreading Rate - 7.2 M2/L depending on application equipment and surface profile

Fineness of Grind - 25 Microns

Solids - 40% by volume

Coverage - 5 – 6 M2 per litre per coat

Primer - Not required for well prepared floor and more than one coat application.

Thinner - Ready for use for brush and roller application, but may be thinned with Epoxy Thinners ONLY if required.

Thinning Ratio - Up to 5 % by volume if desired.

Method of Application - Brush and Roller application recommended. For best results two coats should be applied.

Touch Dry - 4 hours

Hard Dry - 16 hours. Maximum resistance properties for Epoxy Floor Coating developed after 7 days.

Surface Preparation - Ensure floor to be painted is completely dry, minimum 21 days under ambient temperature conditions for new floors. Remove laitance with dilute Hydrochloric Acid, rinse thoroughly with water using hard broom and allow floor to dry. Ensure all oily and grease contamination is removed with appropriate solvent.

Shelf Life - 2 years minimum for unmixed Base and Hardener.

NOTE: Epoxy Floor coating should not be applied under humid conditions as the dry film forms white spots due to reaction of Amine Hardener with moisture in a phenomenon called Moisture Blush

Bitumen Paint

Description

Splash Bitumen Paint is a solvent-based general purpose black paint that is made from a special grade of solid bitumen. The bitumen, supplied in solid form, is melted and dissolved in an aliphatic hydrocarbon solvent. Splash Bitumen paint is used for water-proofing and protecting steelwork against corrosion. It is also used for painting concrete and potable water tanks.

 

Properties

Vehicle type: Bitumen

Solvent: Paraffin/White Spirit

Finish: High gloss

Pigment type: N/A

Colour range: Brownish black.

Thinner:  Turpentine

Drying time: surface dry: 10 minutes at 25 degrees Celcius

Hard dry: 4 hours

Coverage: 5 - 6 square metres per litre at DFT 50 microns.

Pack size: 5 litre, 1 litre

Life span of coating: Bitumen paint coating has a lifespan of up to 6 years on a properly prepared substrate.

Shelf life: 2 years in a properly filled container. Half filled container results in the development of a skin at the surface and gradual thickening of the product. Viscosity is dependent on temperature, with low temperatures increasing the viscosity and high temperatures lowering the viscosity.

 

Application method

Bitumen Paint is applied by brush, dipping, or spraying.

 

Compatibility with other paints

Paints based on strong solvents are not recommended to be applied on top of Bitumen paint as the bitumen dissolves in them causing discolouration of the topcoat.

 

Surface preparation

All surfaces should be clean, free of oil, grease, dirt, rust, or any loose flakes. For rough surfaces, the sandpaper of the right grit or mechanical abrading should be used to obtain a smooth finish onto which paint can easily adhere.

 

STORAGE CONDITIONS

Paint should be stored at room temperature away from direct sunlight or freezing conditions. Tins of paint should be kept full to avoid skinning and gelling.

Chalkboard Paint

Brief description

Splash Paints & Plastics Chalkboard is an alkyd-based paint that dries to a matt finish. It is available in black and green colours. It provides ease of removal of chalk markings using a suitable chalkboard duster.

Controlled pigment grinding during manufacture results in a uniform matt finish which ensures minimum chalk dust during writing on boards made from various materials such as cement plaster and timber boards.

Application

Splash Paints & Plastics Chalkboard paint is easy to apply using a brush, spraying, or roller and the quick-drying characteristic ensures the school board is readily available after painting thereby causing minimum disruptions to lessons.

Splash Paints & Plastics Chalkboard paint is made ready for use but can be thinned with toluene or xylene when the need arises.

Splash Paints & Plastics continues to manufacture a durable chalkboard paint to cater for establishments which cannot afford the financial resources to acquire the latest synthetic boards and the associated marking pens.

Details, Available in 5 Litres

Aluminium Paint

Epoxy Floor Coating

Bitumen Paint

Chalkboard Paint